| Direct measuring system |
Direct path measuring system |
| Cabine |
Full protection cabin |
| Dynamic package for DMF 260 linear
(Y1100) |
Dynamic package for DMF 260 linear (Y1,100 mm)
linear drive X-axis with 80 m/min // 262.48 ft/min rapid move XYZ
80/60/60 m/min // 262.48/196.86 ft/min, Acceleration XYZ 5/6/6 m/s²
// 16.4/19.68 ft/s² Active chiller for main spindle and Linear motor
mag |
| Rigid table with integrated rotary axis
(leftside) |
Rigid table with integrated round table d 1050 mm
// 41.3 in, located in the left working area table load max. 1,200
kg// 2,644 lbs hydraulic clamped in position |
|
Table surface 3200 x 1100 (Ø 1050) mm |
|
Slot width 18 mm |
|
Distance between T-Slots 100 mm |
|
Number of Slots 9 |
|
Rotation speed max.4. Axis 50 rpm |
| Removable partition wall DMF260
(Y1100) |
Partition wall removable for pendulum machining
DMF260, 2 working spaces (possible with integrated round table) |
| Tool magazine 60 positions |
Tool magazine with 60 positions, chain type with
double gripper |
| Spindle speed 20 - 10,000 rpm |
Spindle speed 20 - 10,000 rpm HSK-A100 for tool
taper according to DIN69893 with power 44/32 kW // 59.0/42.9 hp with
torque 288/187 Nm (40/100% ED) |
| 3D quickSET elevated constructuion |
3D quickSET Tool kit for control and compensation
of the cinematic accuracy of 5 axis machine configurations include
additional fixture for elevated construction (only with option touch
probe) |
| Oil mist separator |
Oil and emulsion mist separator system 2 pieces
per machine implemented in right and left cabin side wall. mechanical
filter system 2x1600 m³/h |
| Signal lamp 4-colour |
Signal lamp 4-colour Red: general error Yellow:
intervention necessary Green: automatic mode Blue: set-up mode |
| Air blast through spindle centre |
Air blast through spindle centre activated by M
function, maintained air, low oil D41152871 rate possible |
| Inner coolant supply 40Bar/980l |
Internal coolant supply (ICS) with paper type
filter 40 Bar/980 l // 580 psi/258.8 gallon inclusive 2 rotating clear
window, air purge for linear measuring system, rotary joint for main
spindle |
| Chip flushing for working area |
Flushing for working area Additional flushing of
the working area doors and cabin sidewalls, Bed flushing included |
| Door drive for working area doors |
Door drive for working area doors Open / close -
activated by two-hand-operation at the control panel Safety sensor
technology for prevention of accidents |
| MPC Machine Protection Control |
MPC Machine Protection Control Machine protection
by quick shutdown |
| Application Tuning Cycle ATC |
Application Tuning Cycle ATC programmable feed
parameter selection for machining task: accuracy/surface/speed |
| Operation mode 4 |
Operation mode 4 Process monitoring in the
production Manual intervention with open doors of machining area.
Release after check list has been filled in. |
|
|
| Digital Manufacturing Package |
Digital Manufacturing Package (1) IoTconnector
Allows the use of the Online services from DMG MORI (2) Machine Data
Connector (MDC) Standardized machine data interface Protocols: OPCUA,
MTConnect, MQTT (3) NETservice Qualified support through
internet-b |
| Messenger V4 |
The latest version of DMG MORI Messenger displays
web based the machine live status. It allows to analyze the machine
run-time, downtime, alarms in individually configurable dashboards
and transparently shows the actual status in the manufacturing
shop |
| Service Agent |
Service Agent Overview of all maintenance work on
the machine |